Menu

Technical Details

CPVC Pipes in SDR 13.5

ASTM D–2848 STANDARD DIMENSIONS

Nominal
Bore		 Nominal
Outerside
Diameter		 Wall Thickness,
in (mm)		 Working
Pressure
(Inch) (mm) (mm) (Min) (Max) ((27 °C) Kg/Cm2 (82 °C) Kg/Cm2
1/2" 15 15.90 1.4 1.9 21.8 5.5
3/4" 20 22.20 1.7 2.2 21.8 5.5
1" 25 28.60 2.1 2.6 21.8 5.5
1 ¼ " 32 34.9 2.6 3.1 21.8 5.5
1 ½ " 40 41.30 3.1 3.6 21.8 5.5
2" 50 54 4.0 4.6 21.8 5.5

CPVC Pipes in SDR 11

ASTM D–2846 STANDARD DIMENSIONS

Nominal
Bore		 Nominal
Outerside
Diameter		 Wall Thickness,
in (mm)		 Working
Pressure
(Inch) (mm) (mm) (Min) (Max) ((27 °C) Kg/Cm2 (82 °C) Kg/Cm2
1/2" 15 15.9 1.7 2.2 27.6 6.8
3/4" 20 22.20 2 2.5 27.6 6.8
1" 25 28.60 2.6 3.1 27.6 6.8
1 ¼ " 32 34.9 3.2 3.7 27.6 6.8
1 ½ " 40 41.30 3.8 4.3 27.6 6.8
2" 50 54 4.9 5.5 27.6 6.8

Additional Information

Do's

  • Use pipes,manufactured by Anlon Industries for best results.
  • Installation should be completed as per instructions and recommended safe practices must be followed.
  • Clean the pipe and fittings with a clean dry cloth to remove any dirt.
  • Keep pipe and fittings in the original packaging until needed.
  • Cut the pipe as square or perpendicular as possible before making a joint.
  • Ensure no sharp edges are in contact with the fittings surface while inserting the pipe.
  • Ensure proper alignment of pipe and fittings to avoid stress on the joints.
  • Ensure installation is done in such a way that there are no chances of air entrapment.
  • Use only teflon tape as a thread sealant.
  • Always conduct hydraulic pressure testing after installation to detect any leaks and faults.
  • Wait for the appropriate cure time before pressure testing. Fill lines slowly and allow air to escape from the system prior to pressure testing.
  • Paint pipes exposed to sunlight with a water-based paint.
  • Provide additional support to the brass side of CPVC/brass transition or other for keeping any heavy object to support the weight of the metal system.

Dont's

  • Do not use metal hooks or nails to support/hold or put pressure on the pipes.
  • Do not use straps and hangers with rough or sharp edges. Do not tighten the straps over the pipes.
  • Never expose the pipe to open flame while trying to bend it.
  • Do not drop pipes on edges from heights. Do not drop heavy objects on pipes or walk on pipes.
  • Do not use air or gases for pressure testing.
  • Do not use any other petroleum or solvent-based sealant, adhesive, lubricant or fire-stop material on CPVC pipes & fittings.
  • Do not use CPVC pipes and fittings for pneumatic applications.
  • Do not use the CPVC piping system to support any metallic components.
  • Do not use CPVC solvent cement that exceeds its shelf life, has become discoloured or has gelled.